Ericsson EDACS Station GETC1e 19D901868G4 Manual de instalación descargar pdf (Pagina 17)

CONFIGURATION LBI-38987B

1. Replace Group 5 GETC PROM with original

software.

2. Reload original Turbo software using PC

Programmer.

3. If changes were made to the personality, then

reload the previous parameters.

4. The Speedy microprocessor upgrade, if installed,

does not need to be reversed.

If the original equipment was a GETC (GETC with no

Turbo) platform, then perform the following steps::

1. Replace Group 5 GETC PROM with original software.

2. Disable the Turbo by sliding Turbo switches S2 and S3

toward the front of the GETC shelf.

3. Re-install the original personality EEPROM, if it was

removed, else no change.

4. The Turbo upgrade, if installed, does not need to be

reversed.

5. Re-install the original microprocessor. The Speedy

microprocessor upgrade is not compatible with original

344A3835 software.

Downlink GETC

When configuring the SCAT station’s Downlink GETC,

refer to LBI-38896.

NOTE

When the SCAT Station GETC is upgraded to

349A9607G5 software, the SCAT Downlink GETC

software 344A3835G2 with Turbo Board software

344A4414G2 must be replaced by Link software

344A4895G5 with Link Turbo software

350A1121G5, respectively. Refer to LBI-38896,

Downlink GETC Configuration Manual for details.

TURBO BOARD SOFTWARE

INSTALLATION

This procedure provides instructions for downloading

the Turbo software. The software is included in the Turbo

Media Kit, 344A4414. The installation process involves

downloading the GETC1E utilities to an IBM compatible

personal computer (PC), and connecting the programming

cable (TQ-3360) between the PC and the Turbo Board

programming connector.

When using PC Programmer TQ-3357 V3 (or earlier)

and downloading 344A4414G3 (and earlier) software, the

data from the PC files is routed to the Turbo Board

microprocessors through Turbo Board programming

connector J100 at the rear of the GETC Shelf.

When using PC Programmer TQ-3357 V4.03 (or later),

the Turbo software is downloaded to the Turbo Board

microprocessors through Turbo Board programming

connector J104. Programming through J104 also allows you

to load the GETC personality without changing setups. In

addition, the V4.03 PC Programmer will diagnose any

problems between the PC and the GETC during the

downloading process and simplify the handling and

archiving of the Turbo software.

NOTE

PC Programmer TQ-3357 V4.03 must be used

when upgrading to 349A9607G5 (or later). Only

TQ-3357 V4.03 (or later) is capable of using Field

Macros. When using 349A9607G5 software, the

Field Macro “

gtc_9505.mac

” must be installed

into TQ-3357 to access the new features’

parameters.

Equipment Required

•

IBM PC/XT/AT or compatible with at least 640K

memory, monitor and keyboard running MS-DOS

version 3.0 or higher.

•

Hard disk is recommended; but, not required.

•

Serial Port configured as either COM1 or COM2.

•

TQ-3360 programming cable.

•

Male DB-25 to female DB-9 adapter or cable if the

PC's serial port connector is a male DB-9 connector

instead of a male DB-25 connector.

•

Station Turbo Software distribution diskette

344A4414G5 required when installing

349A9607G5 GETC Software). Refer to SRN1060

and SRN1062 to verify software compatibility.

•

Field Macro “

gtc_9505.mac

” (supplied with the

Station Turbo Software distribution disk).

PC Programmer Setup

Prepare the PC for programming the GETC Turbo

Board by performing the following steps:

NOTE

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 33 34

Comentarios a estos manuales

Sin comentarios

Ericsson EDACS Station GETC1e 19D901868G4 Manual de instalación Pagina 17

Comentarios a estos manuales