Ericsson EDACS Station GETC1e 19D901868G4 Manual de instalación Pagina 18
- Pagina / 56
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
LBI-38988
18
12345678
OPEN
S2
12345678
OPEN
S3
12345678
OPEN
S1
CCCCC C CCC CC CCC
OOO
CC
Front of GETC Legend: C = Closed O = Open
CCCCC
Figure 6 - DIP Switch Settings
3. Reset the GETC by either applying power or pressing
the GETC RESET switch S4, see Figure 4, located just
below the DIP switches. Resetting the GETC, in
combination with the DIP switch settings, places the
GETC into the Personality Programming mode.
4. Verify that front panel LEDs L3, L4, and L5 are ON, as
shown in Table 1. This indicates the GETC is ready for
programming.
Table 1 - Indicators in Programming Mode Using J100
LED Indicators L1 L2 L3 L4 L5 L6 L7
Programming Mode
❍❍●●●❍❍
Legend:
❍
= OFF
●
= ON
❉
= FLASHING
5. Proceed with the Personality programming as described
in TQ-3357.
6. After saving the personality and downloading it into the
GETC, perform an operational checkout of the GETC.
Programming a Personality Through J104
When using TQ-3357 version 4 (or later) program the
personality through J104.
1. One end of the serial programming cable (TQ-3360)
should be connected to the computer. The other end of
the serial cable connects to the GETC Shelf connector
J104. See Figure 7.
2. Move Switch S2 on the Turbo Board to the front
placing the GETC into the Personality Programming
mode. See Figure 7.
3. Verify that front panel LEDs L6 and L7 are flashing, as
shown in Table 2. This indicates the GETC is ready for
programming.
Table 2 - Indicators in Programming Mode Using J104
LED Indicators L1 L2 L3 L4 L5 L6 L7
Programming Mode
❍❍❍❍❍
❉❉
Legend:
❍
= OFF
●
= ON
❉
= FLASHING
S4
S3S2S1
L1 L2 L3 L4 L5 L6 L7
T1 T2
U18R1
1
1
1
1
1
U19
U3
U2
U1
U4
J3
J49
J27
J10
J9 J8 J5
J19
J7
TP107
U1
U2
Software Disk
TQ3357 V4 or later
To
COM Port
Turbo Board GETC Logic Board
J103 J104
J2
J3
Harness
19C337712G1
TQ-3360
TQ-3357
S2
S3
GETC Shelf 19D901868G3
Cable
Figure 7 - System Hook-Up Using J104
- Configuration Manual 1
- INTRODUCTION 7
- RELATED PUBLICATIONS 7
- DESCRIPTION 8
- OPERATION 8
- 9600 baud Modem Data 9
- 4-Wire Audio Circuits 9
- LBI-38988 10
- CONFIGURATION 11
- TROUBLESHOOTING 23
- LBI-38988 24
- APPENDIX A 31
- S1-1 S2-1 S1-1 S2-1 S1-1 S2-1 32
- APPENDIX B 45
- Printed in U.S.A 50
- APPENDIX D 51
- INTERCONNECTION DIAGRAM 52
- GETC JUMPER DIAGRAM 55
Relacionado con productos y manuales para Arrancadores remotos Ericsson EDACS Station GETC1e 19D901868G4
(58 paginas)Kuzma STOGI 130419 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Audio-Zubehör Kuzma STOGI 130419.
Wir stellen 1 PDF-Handbücher Kuzma STOGI 130419 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comentarios a estos manuales