Ericsson 1553-FGC 101 1010 Uen A Guía de usuario Pagina 19
- Pagina / 196
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Introduction to the EQ8096
1.4 Guided Tour
1.4.1 Enclosure
The enclosure is 2U and is used as a stand-alone unit. All inputs and outputs are via
rear panel connectors, with the exception of the LCD and button input at the front of
the unit (for setting IP address).
1.4.2 Front Panel Description
The Front panel of the EQ8096 is fitted with a single power supply unit (PSU1) as
standard and may be optionally fitted with a second power supply (PSU2) to provide
1+1 redundancy. When two power supplies are fitted, they operate in load sharing
mode. Both are secured by clips and, if required, may be removed from the front of
the unit. On the left hand side of the panel is a 2-line LCD display which may be
used for local control configuration (see Chapter 2, Installing the Equipment for
details).
1.4.2.1 Front Panel LEDs
There are 7 LED indicators, 3 located on the left of the front panel and 4 located
across both power supplies, when fitted (see Figure 1.2 and Table 1.9).
Table 1.9 Front Panel Indicators
Indicator Color Description
Alarm Red This LED is lit when an alarm condition has been detected.
Power Green This LED is lit when power is being received.
Active
(DTI lock)
Blue
This LED is lit when the DTI client card is locked to the DTI
server (M-CMTS only).
PSU Power
x 2
Green This LED is lit when the power supply is in use
PSU Fault
x 2
Amber
This LED is lit when a fault condition is detected in the power
supply
2/1553-FGC 101 1019 Uen A
1-11
- EQ8096 Universal Edge QAM 1
- Introduction 4
- Revision History 4
- Associated Documents 4
- Trademarks 4
- Warnings, Cautions and Notes 5
- EMC Compliance 6
- Contact Information 6
- Preliminary Pages 7
- Preliminary Pages 8
- 1 Introduction to the EQ8096 9
- Introduction to the EQ8096 10
- 2/1553-FGC 101 1019 Uen A 10
- Caution! 11
- Warning! 11
- 1.2 Summary of Features 13
- 1.2.2 Data Input 14
- Introduction to the EQ8096 15
- 1.3 Output Channel Mappings 16
- 1.3.2 UDP Port Mapping 18
- 1.4 Guided Tour 19
- 1.4.3 Front Panel Controls 20
- 2 Installing the Equipment 23
- Installing the Equipment 24
- 2.1 Introduction 25
- 2.2 Preliminary Checks 26
- Cautions! 27
- Warnings! 29
- 2.5 -48 V DC Power Supply 31
- 2.5.3 DC Connector Details 33
- 2.6 Signal Connections 34
- 2.6.4 Control 36
- 2.6.7 ASI Monitor port 36
- 2.6.8 Host Status 36
- 2.7 Indicators 37
- 2.7.2 Rear Panel 38
- Chapter 3 39
- 3.1 Introduction 43
- 3.3 Web Page Menus 45
- 3.3.3 Data Port Settings 50
- 3.3.4 Modulation Settings 52
- 3.4.4 Broadcast Mode 61
- 3.4.5 DEPI/M-CMTS Mode 67
- 3.5.1 Overview 67
- 3.5.2 CA ECMG Settings 68
- 3.5.3 CA Settings 69
- 3.6 Engineering Tabbed Page 70
- 4 Alarms 75
- Alarms 76
- 4.1 Introduction 77
- 4.2 View Active Alarm Table 78
- 4.3 Configure Active Alarms 78
- 4.4 Specific Alarms 79
- 4.4.5 Temperature Alarms 81
- 4.5 Trap Destination Table 82
- 4.6 Status Indicators 83
- 4.7 Unit Alarm List 84
- Alarms 85
- Using XML File Download 97
- 5.1 Introduction 99
- 5.2 FTP File Transfer 99
- 5.3 XML Files 99
- 5.3.1 XML File Format 100
- 5.3.2 Status File Examples 100
- 2/1553-FGC 101 1019 Uen A 101
- 5.4.1 EMM Connections 105
- 5.4.4 Multiple EMM Streams 108
- 5.4.7 Stopping Encryption 110
- 5.4.8 Simulcrypt 111
- 5.5 Errors during FTP 113
- 5.8 Redundancy Switch 116
- Chapter 6 117
- Contents 117
- 6.1 Introduction 119
- 6.2 Preventive Maintenance 119
- 6.3 Alarms 120
- 6.4 Fault-finding 121
- 6.5 Power Supply Problems 123
- Chapter 7 127
- 7.1 Introduction 129
- 7.2 How to Install Software 129
- 7.4 Requesting a Key 130
- Information’ tab 132
- 8 Unit Configuration via FTP 133
- Unit Configuration via FTP 134
- 8.1 Introduction 135
- Output Option Cards 137
- 9.1 Introduction 139
- 9.3.1 Preparing the Unit 143
- 9.3.5 Reconfigure the Unit 145
- Specification 147
- 10.1 General 149
- 10.3.1 System Setup 151
- 10.3.2 M-CMTS Session Setup 151
- 10.3.4 DTI Card 157
- A Glossary 159
- Glossary 160
- Glossary 161
- B Technical Specification 179
- Technical Specification 180
- B.1 Unit Specification 181
- B.2 Rear Panel Connectors 182
- B.2.3 RF Output 183
- Parameter Requirement 184
- B.2.5 Ethernet Control 185
- Technical Specification 187
- B.3 Power Supply 188
- B.4 Physical Details 189
- B.6 Compliance 190
- B.6.3 Telecommunications 191
- B.6.4 CE Marking 191
- B.6.5 C-Tick Mark 191
- B.6.6 Packaging Statement 192
- B.6.7 Packaging Markings 192
- B.6.9 Equipment Disposal 194
- B.6.10 Recycling 194
- B.7 Cable Types 195
Relacionado con productos y manuales para Receptor Ericsson 1553-FGC 101 1010 Uen A
Receptor Ericsson RX8000 Series Especificaciones
(37 paginas)
(37 paginas)
Receptor Ericsson RX8000 Series Especificaciones
(26 paginas)
(26 paginas)
Receptor Ericsson RX8330 Especificaciones
(39 paginas)
(39 paginas)
Receptor Ericsson TT1222 Guía de usuario
(198 paginas)
(198 paginas)
Receptor Ericsson RX8200 Manual de usuario
(8 paginas)
(8 paginas)
Receptor Ericsson LBI-38505A Manual de usuario
(197 paginas)
(197 paginas)
Receptor Ericsson TT1222 Guía de usuario
(20 paginas)
(20 paginas)
Receptor Ericsson RX8315 Guía de usuario
(40 paginas)
(40 paginas)
Receptor Ericsson RX8200 Guía de usuario
(44 paginas)
(44 paginas)
Receptor Ericsson RX8315 Guía de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales