Ericsson 1553-FGC 101 1010 Uen A Guía de usuario Pagina 43
- Pagina / 196
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operating the EQ8096 Using the Web Browser
3.1 Introduction
Standard configuration instructions are given in the User Guide. This chapter gives
further information on the operation of the unit and describes additional functions not
required for everyday operation.
3.2 Establishing a Connection
3.2.1 Assigning a Control IP Address
All EQ8096 units are shipped with an invalid Control Port IP address of 0.0.0.0. This
must be configured to a local valid IP address before the product can be fully
configured. This can be performed using the Front Panel Keypad (see Table 2.6) or
via RS-232:
1. Connect a cable between the Host Status port on the EQ8096
(9-way male D-Type) and a local PC using a straight through RS-232 cable.
2. Using a suitable terminal emulator on the PC, Set up the communication
parameters.
Note: The serial port communications defaults to 115200 bit/s, 8 bit data, no
parity, 1 stop bit.
3. Power cycle the EQ8096. The terminal emulator will display a boot sequence
that will show the software version and control port IP settings. If the IP address
is still at the factory default of 0.0.0.0 for all 4 ports, then the user will be required
to assign a valid address to any of these.
4. Using the terminal, the user should enter the local IP address allocated to the
unit using the command IPn xxx.xxx.xxx.xxx
(e.g. IP3 172.17.124.3) and then press return. ‘n’ is the control port index (1 – 4)
as outlined below:
a CA Main
b CA Redundant
c Control Main
d Control redundant
e The IP settings are effective immediately.
Note: Since the default Gateway IP address is not set in the unit, the user will only
be able to establish an Ethernet connection from an IP address on the same
Sub-net. See Section 3.2.2 for description of how to set Subnet mask +
gateway address.
2/1553-FGC 101 1019 Uen A
3-5
- EQ8096 Universal Edge QAM 1
- Introduction 4
- Revision History 4
- Associated Documents 4
- Trademarks 4
- Warnings, Cautions and Notes 5
- EMC Compliance 6
- Contact Information 6
- Preliminary Pages 7
- Preliminary Pages 8
- 1 Introduction to the EQ8096 9
- Introduction to the EQ8096 10
- 2/1553-FGC 101 1019 Uen A 10
- Caution! 11
- Warning! 11
- 1.2 Summary of Features 13
- 1.2.2 Data Input 14
- Introduction to the EQ8096 15
- 1.3 Output Channel Mappings 16
- 1.3.2 UDP Port Mapping 18
- 1.4 Guided Tour 19
- 1.4.3 Front Panel Controls 20
- 2 Installing the Equipment 23
- Installing the Equipment 24
- 2.1 Introduction 25
- 2.2 Preliminary Checks 26
- Cautions! 27
- Warnings! 29
- 2.5 -48 V DC Power Supply 31
- 2.5.3 DC Connector Details 33
- 2.6 Signal Connections 34
- 2.6.4 Control 36
- 2.6.7 ASI Monitor port 36
- 2.6.8 Host Status 36
- 2.7 Indicators 37
- 2.7.2 Rear Panel 38
- Chapter 3 39
- 3.1 Introduction 43
- 3.3 Web Page Menus 45
- 3.3.3 Data Port Settings 50
- 3.3.4 Modulation Settings 52
- 3.4.4 Broadcast Mode 61
- 3.4.5 DEPI/M-CMTS Mode 67
- 3.5.1 Overview 67
- 3.5.2 CA ECMG Settings 68
- 3.5.3 CA Settings 69
- 3.6 Engineering Tabbed Page 70
- 4 Alarms 75
- Alarms 76
- 4.1 Introduction 77
- 4.2 View Active Alarm Table 78
- 4.3 Configure Active Alarms 78
- 4.4 Specific Alarms 79
- 4.4.5 Temperature Alarms 81
- 4.5 Trap Destination Table 82
- 4.6 Status Indicators 83
- 4.7 Unit Alarm List 84
- Alarms 85
- Using XML File Download 97
- 5.1 Introduction 99
- 5.2 FTP File Transfer 99
- 5.3 XML Files 99
- 5.3.1 XML File Format 100
- 5.3.2 Status File Examples 100
- 2/1553-FGC 101 1019 Uen A 101
- 5.4.1 EMM Connections 105
- 5.4.4 Multiple EMM Streams 108
- 5.4.7 Stopping Encryption 110
- 5.4.8 Simulcrypt 111
- 5.5 Errors during FTP 113
- 5.8 Redundancy Switch 116
- Chapter 6 117
- Contents 117
- 6.1 Introduction 119
- 6.2 Preventive Maintenance 119
- 6.3 Alarms 120
- 6.4 Fault-finding 121
- 6.5 Power Supply Problems 123
- Chapter 7 127
- 7.1 Introduction 129
- 7.2 How to Install Software 129
- 7.4 Requesting a Key 130
- Information’ tab 132
- 8 Unit Configuration via FTP 133
- Unit Configuration via FTP 134
- 8.1 Introduction 135
- Output Option Cards 137
- 9.1 Introduction 139
- 9.3.1 Preparing the Unit 143
- 9.3.5 Reconfigure the Unit 145
- Specification 147
- 10.1 General 149
- 10.3.1 System Setup 151
- 10.3.2 M-CMTS Session Setup 151
- 10.3.4 DTI Card 157
- A Glossary 159
- Glossary 160
- Glossary 161
- B Technical Specification 179
- Technical Specification 180
- B.1 Unit Specification 181
- B.2 Rear Panel Connectors 182
- B.2.3 RF Output 183
- Parameter Requirement 184
- B.2.5 Ethernet Control 185
- Technical Specification 187
- B.3 Power Supply 188
- B.4 Physical Details 189
- B.6 Compliance 190
- B.6.3 Telecommunications 191
- B.6.4 CE Marking 191
- B.6.5 C-Tick Mark 191
- B.6.6 Packaging Statement 192
- B.6.7 Packaging Markings 192
- B.6.9 Equipment Disposal 194
- B.6.10 Recycling 194
- B.7 Cable Types 195
Relacionado con productos y manuales para Receptor Ericsson 1553-FGC 101 1010 Uen A
Receptor Ericsson RX8000 Series Especificaciones
(37 paginas)
(37 paginas)
Receptor Ericsson RX8000 Series Especificaciones
(26 paginas)
(26 paginas)
Receptor Ericsson RX8330 Especificaciones
(39 paginas)
(39 paginas)
Receptor Ericsson TT1222 Guía de usuario
(198 paginas)
(198 paginas)
Receptor Ericsson RX8200 Manual de usuario
(8 paginas)
(8 paginas)
Receptor Ericsson LBI-38505A Manual de usuario
(197 paginas)
(197 paginas)
Receptor Ericsson TT1222 Guía de usuario
(20 paginas)
(20 paginas)
Receptor Ericsson RX8315 Guía de usuario
(40 paginas)
(40 paginas)
Receptor Ericsson RX8200 Guía de usuario
(44 paginas)
(44 paginas)
Receptor Ericsson RX8315 Guía de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.175 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales